CommunityServer.Discussions.Components.Files/3514/7215.power-tab.jpg' alt='Usb Serial Adapter Driver Microsoft Office' title='Usb Serial Adapter Driver Microsoft Office' />Cisco 3.Series and Cisco 2.Series Hardware Installation Guide Installing and Connecting the Router Cisco 2.Series Integrated Services RoutersInstallation Requirements and Warnings.Warning.To see translations of the warnings that appear in this publication, see the Regulatory Compliance and Safety Information for Cisco 2.Series Integrated Services Routers or the Regulatory Compliance and Safety Information for Cisco 3.Series Integrated Services Routers document.Usb Serial Adapter Driver Microsoft Office' title='Usb Serial Adapter Driver Microsoft Office' />Only trained and qualified personnel should be allowed to install, replace, or service this equipment.Statement 1.Warning This unit might have more than one power supply connection.All connections must be removed to de energize the unit.Statement 1.Warning Blank faceplates and cover panels serve three important functions they prevent exposure to hazardous voltages and currents inside the chassis they contain electromagnetic interference EMI that might disrupt other equipment and they direct the flow of cooling air through the chassis.Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place.Statement 1. How To Install A Pocket Door Frame From Home Depot . Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON.CAN USB The SYS TEC CAN USB Adapter were designed to provide a lowcost CANbus interface solution for connecting the CANbus to the PC via USB.CAN USB driver.Amazon.Plugable USB Audio Adapter with 3.SpeakerHeadphone and Microphone Jacks Black Aluminum CMedia HS 100B Chip BuiltIn Compatibility with Windows.To avoid electric shock, use caution when working near WAN ports.When detaching cables, detach the end away from the unit first.Statement 1.Warning This equipment must be grounded.Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor.Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.Statement 1.Warning Before opening the unit, disconnect the telephone network cables to avoid contact with telephone network voltages.Statement 1.Warning Do not use this product near water for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.Statement 1.Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.Statement 1.Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.Statement 1.Warning Avoid using a telephone other than a cordless type during an electrical storm.There may be a remote risk of electric shock from lightning.Usb Serial Adapter Driver Microsoft Office' title='Usb Serial Adapter Driver Microsoft Office' />Statement 1.Warning To report a gas leak, do not use a telephone in the vicinity of the leak.Statement 1.Warning.This unit is intended for installation in restricted access areas.A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security.Statement 1.Warning.Blank faceplates and cover panels serve three important functions they prevent exposure to hazardous voltages and currents inside the chassis they contain electromagnetic interference EMI that might disrupt other equipment and they direct the flow of cooling air through the chassis.Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place.Statement 1.Warning The covers are an integral part of the safety design of the product.Do not operate the unit without the covers installed.Statement 1.Installing the Router.If you need to install service modules, interface cards, and FRUs, you can install them either before or after you install the router.Ideally, you install modules and interface cards when you have the best access to the back panel of the router.Internal modules and FRUs, such as internal services modules ISMs or packet voice data modules PVDMs, and fan trays should be installed before rack mounting.See the Installing and Upgrading Internal Modules and FRUs section.There are three methods of installing the router Warning Before working on a system that has an onoff switch, turn OFF the power and unplug the power cord.Statement 1.Caution To prevent damage to the chassis, never attempt to lift or tilt the chassis by holding it by the plastic panel on the front.Download Jalwa Song Of Fashion Movie Bollywood .Always hold the chassis by the sides of the metal body.Rack Mounting the Chassis.Cisco 2.EIA and 2. 3 inch 5.Southwestern Bell Corporation SBC racks.The Cisco 3.ETSI rack. Use the standard brackets shipped with the router for mounting the chassis in a 1.EIA rack you can order optional larger brackets for mounting the chassis in a 1.SBC rack.You can mount the router in the following ways Center front mountingBrackets attached in the center front of the chassis with only the front panel facing forward.Center back mountingBrackets attached in the center back of the chassis with only the back panel facing forward.Front mountingBrackets attached at the front of the chassis with the front panel facing forward.Back mountingBrackets attached at the back of the chassis with the back panel facing forward.Attaching Rack Mount Brackets to Cisco 2.Routers.For the Cisco 2.Phillips flat head screws to attach the long side of each bracket to the router.For the Cisco 3.Phillips flat head screws to attach the long side of each bracket to the router.Figure 3 1 Bracket Installation for Front Mounting.Bracket Installation for Back Mounting shows how to attach the brackets to the sides of the router with the back panel forward.Figure 3 2 Bracket Installation for Back Mounting.Bracket Installation for Center Mounting shows how to attach the brackets to the sides of the router with center mounting.Figure 3 3 Bracket Installation for Center Mounting.Attaching Rack Mount Brackets to Cisco 2.Cisco 2.Cisco 2.Routers. Attach the mounting brackets to the router chassis as shown in Figure 3 4 through Figure 3 7, using the screws provided.Caution Do not over torque the screws.The recommended torque is 1.N m.Attach the second bracket to the opposite side of the chassis.Use a number 2 Phillips screwdriver to install the number 8 bracket screws.Caution Your chassis installation must allow unrestricted airflow for chassis cooling.Figure 3 4 Bracket Installation for Front Mounting.SBC1 brackets.EIA brackets. Figure 3 5 Bracket Installation for Center Front Mounting.SBC brackets.EIA brackets. Figure 3 6 Bracket Installation for Back Mounting.SBC brackets.EIA brackets. Figure 3 7 Bracket Installation for Center Back Mounting.SBC brackets.EIA brackets. Attaching Rack Mount Brackets to Cisco 3.Series Routers.Attach the mounting brackets to the router chassis as shown in Figure 3 8 through Figure 3 1.Caution Do not over torque the screws.The recommended torque is 8 to 1.N m.Attach the second bracket to the opposite side of the chassis.Use a number 2 Phillips screwdriver to install the number 6 bracket screws.Caution Your chassis installation must allow unrestricted airflow for chassis cooling.Figure 3 8 Bracket Installation for Front Mounting.EIA brackets.EIA brackets. Figure 3 9 Bracket Installation for Center Front Mounting.EIA brackets.EIA brackets. Figure 3 1.Bracket Installation for Rear Mounting.EIA brackets.EIA brackets. Figure 3 1.Bracket Installation for Center Rear Mounting.EIA brackets.EIA brackets. Mounting the Router in a Rack.After you attach the rack mount brackets to the router chassis, use the screws provided with the rack to install the chassis in the rack.See Figure 3 1.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |